Comprehensive HVAC Glossary

Plain-English definitions of common heating, ventilation, and air conditioning terms, with Central Texas context where applicable. Select a letter to jump to that section.

A · B · C · D · E · F · G · H · I · L · M · N · O · P · R · S · T · U · V · W · Z

A

A2L Refrigerant

A refrigerant classified as having lower toxicity and lower flammability under ASHRAE’s refrigerant safety classification system. R-32 and R-454B are examples used in newer air conditioning equipment designed specifically for them.

AC (Air Conditioning)

A system that cools indoor air by removing heat and transferring it outdoors. Central air conditioning systems also remove some moisture from the air during normal cooling operation. In Central Texas, air conditioning is essential for maintaining indoor comfort during prolonged periods of summer heat.

AC Capacitor

An electrical component that helps start or operate motors in an air conditioning system, depending on its design. A failing capacitor can prevent the compressor or fan motor from operating properly.

AC Compressor

The component that circulates refrigerant through an air conditioning or heat pump system by compressing low-pressure refrigerant vapor into high-pressure vapor. The compressor is located in the outdoor unit of most residential central AC systems.

AC Condenser

The outdoor portion of a typical split air conditioning system, containing the condenser coil, compressor, and fan. It releases heat collected from inside the home into the outdoor air.

AC Tune-Up

A preventive maintenance service that includes inspecting, testing, and servicing key air conditioning components to help maintain safe, reliable, and efficient operation.

AFUE (Annual Fuel Utilization Efficiency)

A percentage that measures how efficiently a furnace converts fuel into usable heat over a typical heating season. A furnace rated at 95% AFUE converts approximately 95% of its fuel energy into usable heat under standardized conditions.

Air Balancing

The process of measuring and adjusting airflow through an HVAC system to distribute conditioned air appropriately throughout a home. Air balancing can help address rooms that receive too much or too little heating or cooling.

Air Changes per Hour (ACH)

A measurement describing how many times the air volume of a space is replaced in one hour through ventilation, infiltration, or a combination of the two.

Air Filter

A component designed to capture airborne particles as air passes through an HVAC system. Filters help protect equipment and, depending on their efficiency, can improve indoor air quality.

Airflow

The movement of air through HVAC equipment, ductwork, and occupied spaces. Proper airflow is necessary for effective heating, cooling, and humidity control.

Air Handler

The indoor equipment responsible for circulating air through an HVAC system. It generally contains a blower motor and may include an evaporator coil, electric heating elements, and other components.

Attic Heat Gain

Heat accumulated in an unconditioned attic can increase a home’s cooling demand when it passes through ceilings or affects poorly insulated ductwork. In Central Texas, where attic temperatures can become extremely hot during summer, proper duct insulation, air sealing, and adequate attic insulation help limit unwanted heat transfer.

Auxiliary Heat (Aux Heat)

Supplemental heating that operates when a heat pump cannot meet the home’s heating demand by itself or under certain operating conditions. In many residential heat pumps, auxiliary heat is provided by electric resistance heating elements.


Back to top ↑

B

Blower Motor

The motor that drives the indoor fan, moving air across the heating or cooling components and through the ductwork. A malfunctioning blower motor can cause weak airflow, uneven temperatures, or system shutdowns.

BTU (British Thermal Unit)

A unit used to measure heat energy. HVAC equipment capacity is commonly expressed in BTUs per hour (BTU/h).

BTU/h

British thermal units per hour, a measurement of heating or cooling capacity. For example, a system rated at 36,000 BTU/h has a nominal capacity of three tons of cooling.

Burner

A furnace component where fuel, typically natural gas or propane, is burned to generate heat. Burners must operate correctly to provide efficient and safe heating.


Back to top ↑

C

CFM (Cubic Feet per Minute)

A measurement of airflow volume indicating how many cubic feet of air move through a system each minute. HVAC technicians use CFM measurements to assess airflow and system performance.

Climate Zone

A geographic classification based on temperature, moisture, and other climate characteristics that influence building design and HVAC requirements. The Austin area is generally classified as Climate Zone 2A, indicating a hot-humid climate, under the International Energy Conservation Code’s climate-zone system.

Cold Climate Heat Pump

A heat pump designed and tested to maintain useful heating capacity and efficiency at relatively low outdoor temperatures. Although Central Texas experiences occasional freezing weather, the appropriate heat pump should be selected based on the home’s heating requirements and local design conditions.

Combustion

The chemical process of burning fuel to release heat. Gas furnaces use controlled combustion to warm a heat exchanger, which transfers heat to the air circulating through the home.

Compressor

A mechanical component that raises the pressure and temperature of refrigerant vapor, allowing it to release heat elsewhere in the refrigeration cycle. See also AC Compressor.

Condensate

Water that forms when moisture in the air condenses on a cold surface. During air conditioning operation, moisture can collect on the evaporator coil and drain away through the condensate system.

Condensate Drain Line

A pipe or tube that carries water collected by the air conditioning system to an appropriate discharge location. Blockages can cause water leaks, drainage problems, or safety-switch shutdowns.

Condensate Drain Pan

A tray that collects water dripping from the evaporator coil so it can drain away. Some installations also have an auxiliary drain pan to protect against overflow.

Condensate Pump

A device that moves collected condensate to a suitable drain when gravity drainage is not practical.

Condenser Coil

The heat-exchanging coil that releases heat from the refrigerant. During normal air conditioning operation, it is located in the outdoor unit.

Condenser Fan

The fan that moves outdoor air across the condenser coil to help release heat. A failed condenser fan may cause high refrigerant pressure, overheating, or system shutdown.

Contactor

An electrically controlled switch that supplies power to components such as the compressor and outdoor fan motor. A defective contactor can prevent the outdoor unit from starting or stopping properly.

Cooling Capacity

Cooling capacity refers to the amount of heat an air conditioning system can remove from an indoor space over a given period. It is typically measured in British Thermal Units per hour (BTU/h) or tons, with one ton of cooling capacity equal to 12,000 BTU/h. For example, a three-ton air conditioner has a nominal cooling capacity of 36,000 BTU/h. The appropriate cooling capacity for a home depends on several factors, including square footage, insulation, ceiling height, windows, and local climate. In Central Texas, where summer temperatures frequently exceed 100°F, proper equipment sizing is especially important. An undersized system may struggle to maintain comfortable temperatures, while an oversized system can cycle too frequently and provide inadequate humidity control.

Cooling Load

The rate of heat removal necessary to maintain desired indoor temperature and humidity conditions. Cooling load depends on factors such as outdoor weather, insulation, windows, air leakage, occupancy, and internal heat sources.

Cycle

One period of HVAC operation between startup and shutdown. The frequency and duration of cycles vary with equipment type, system controls, weather conditions, and the home’s heating or cooling needs.


Back to top ↑

D

Damper

A movable plate or valve inside ductwork that regulates airflow. Dampers may be adjusted manually or controlled automatically as part of a zoning system.

Defrost Cycle

An operating mode that removes frost or ice from a heat pump’s outdoor coil during heating operation. Defrost cycles are normal during certain cold, humid conditions, including some Central Texas winter weather.

Dehumidification

The process of removing moisture from indoor air. Air conditioners provide dehumidification during cooling, while dedicated dehumidifiers are designed specifically for moisture removal.

Delta T (Temperature Differential)

The difference between two measured temperatures. HVAC technicians often evaluate the difference between return-air and supply-air temperatures when diagnosing system performance. The expected difference varies by operating conditions.

Demand Response

A strategy that adjusts electricity consumption in response to utility signals, grid conditions, or electricity prices. Compatible smart thermostats may participate in voluntary demand-response programs.

Dew Point

The temperature at which air reaches saturation and water vapor begins to condense, assuming pressure and moisture content remain unchanged. Dew point is an important measurement in humidity control and air conditioning design.

Dual-Fuel System

A heating arrangement combining an electric heat pump with a gas furnace. The system switches between heating sources based on controls, outdoor conditions, or operating costs.

Duct Leakage

The unintended escape or entry of air through gaps, holes, or poorly connected ductwork. Leaky ducts can waste conditioned air, reduce comfort, and introduce unconditioned air or contaminants.

Ductless Mini-Split

A heating and cooling system that connects one or more indoor units to an outdoor unit through refrigerant lines without requiring conventional central ductwork. Mini-splits are often used for individual rooms, additions, garages, and areas without suitable ducts.

Duct Sealing

The process of closing leaks in ductwork using appropriate materials and methods, such as HVAC-rated mastic or approved sealing products.

Ductwork

The network of ducts that distributes heated or cooled air throughout a building and returns air to HVAC equipment. In many Central Texas houses, ductwork runs through attics, where insulation and proper sealing are especially important.

Ductwork in Unconditioned Attics

Many Central Texas homes have supply and return ducts routed through attic spaces. Because these attics can become extremely hot during summer, poorly sealed or insulated ductwork can contribute to energy loss and reduced cooling performance. Proper duct sealing and insulation help maintain efficiency and prevent unconditioned attic air from entering the duct system.


Back to top ↑

E

ECM (Electronically Commutated Motor)

An electronically controlled motor used in HVAC blowers and other equipment. ECMs can provide more precise speed control and may use less electricity than certain conventional motor designs.

EER2 (Energy Efficiency Ratio 2)

A standardized measure of cooling efficiency at specified test conditions. It compares cooling output in BTU/h with electrical input in watts. Higher ratings indicate greater efficiency under the rated conditions.

Electric Resistance Heat

Heating produced by passing electricity through resistance elements. This technology is commonly used for supplemental or emergency heating in some residential heat pump systems.

Emergency Heat (EM Heat)

A thermostat setting that typically operates a heat pump system’s backup heating source without normal heat-pump heating. It is generally intended for situations where the primary heat pump is unavailable or requires service.

ENERGY STAR

A government-backed energy efficiency certification program that identifies products meeting defined efficiency and performance criteria. ENERGY STAR-certified HVAC products must meet requirements applicable to their equipment category.

ERV (Energy Recovery Ventilator)

A ventilation device that transfers some heat and moisture between incoming outdoor air and outgoing indoor air. ERVs can help reduce the heating and cooling burden associated with providing fresh air, although performance depends on climate and system design.

Evaporator Coil

The heat-exchanging component that absorbs heat from indoor air during cooling operation. As warm, humid air passes over the cold coil, moisture may condense and drain away.

Expansion Valve

A refrigerant-metering component that regulates refrigerant flow and reduces its pressure before it enters the evaporator. Thermostatic and electronic expansion valves are two common types.


Back to top ↑

F

Filter Drier

A sealed refrigeration component that removes moisture and captures certain contaminants circulating in the refrigerant system.

Flame Sensor

A safety component in many gas furnaces that verifies the presence of a burner flame. A dirty or malfunctioning flame sensor can cause a furnace to shut off shortly after ignition.

Flex Duct

Flexible ductwork commonly used to distribute air in residential HVAC systems. Flex ducts must be properly sized, supported, and installed without excessive compression or sharp bends to maintain airflow.

Flue

A passage that carries combustion exhaust gases from fuel-burning heating equipment to a safe outdoor discharge point.

Forced-Air Heating

A heating method that uses a blower and air distribution system to move warmed air throughout a building. Gas furnaces and heat pumps commonly use forced-air distribution.

Furnace

A heating appliance that generates heat and transfers it to air circulated through a building. Residential furnaces commonly operate using natural gas, propane, or electricity.


Back to top ↑

G

Gas Furnace

A heating system that burns natural gas or propane to warm a heat exchanger, which heats air circulated through the home.

Global Warming Potential (GWP)

A measure of how strongly a greenhouse gas contributes to warming over a specified period compared with carbon dioxide. Refrigerants differ significantly in GWP, influencing the selection of newer HVAC refrigerants.


Back to top ↑

H

Heat Exchanger

A component that transfers heat between substances or air streams without intentionally mixing them. In a gas furnace, a heat exchanger transfers heat from combustion gases to circulating indoor air.

Heat Gain

The addition of heat to a building from sunlight, outdoor air, occupants, appliances, and other sources. Solar heat gain through windows and roofs can be particularly significant during Central Texas summers.

Heating Load

The rate of heat that must be supplied to maintain the desired indoor temperature under particular outdoor conditions.

Heat Loss

Heat leaving a building through walls, ceilings, windows, air leakage, and other pathways. Heat loss calculations help determine the heating capacity needed during cold weather.

Heat Pump

A system that uses refrigeration technology to transfer heat rather than generate all heating through combustion or electric resistance. Most residential air-source heat pumps provide both heating and cooling by reversing the direction of heat transfer.

Heat Pump Performance During Freezes

Heat pumps can provide effective heating in Central Texas, but their available heating capacity and efficiency change with outdoor temperatures. During occasional winter freezes, some systems use supplemental heating or periodically enter defrost mode to remove ice from the outdoor coil.

Heat Pump Water Heater

A water heater that transfers heat from surrounding air into water using a refrigeration system. It differs from a conventional electric resistance water heater and from a whole-home space-conditioning heat pump.

HEPA (High-Efficiency Particulate Air)

A high-efficiency air filtration classification. A qualifying HEPA filter captures at least 99.97% of airborne particles measuring 0.3 microns under the applicable test conditions. HEPA filtration is more common in dedicated air-cleaning equipment than in ordinary residential HVAC filter slots.

HFC (Hydrofluorocarbon)

A family of refrigerant chemicals that generally do not deplete the ozone layer but can have significant global warming potential. R-410A is an example of an HFC refrigerant blend.

HSPF2 (Heating Seasonal Performance Factor 2)

A standardized measure of an electric heat pump’s seasonal heating efficiency. It compares heating delivered over a representative season with electrical energy consumed. Higher HSPF2 ratings indicate better rated heating efficiency.

Humidifier

A device that adds water vapor to indoor air to increase humidity. Humidifiers may be used when indoor air becomes excessively dry during heating.

Humidity

The amount of water vapor present in air. High indoor humidity can make a home feel warmer, encourage condensation, and contribute to moisture problems.

Humidity Control

The process of managing indoor moisture levels to maintain comfort and reduce the risk of condensation and mold growth. In Central Texas, outdoor humidity and moisture entering through air leaks can affect indoor comfort. Proper air conditioning equipment sizing, airflow, and operating characteristics help balance temperature control with dehumidification.

HVAC (Heating, Ventilation, and Air Conditioning)

The systems and technologies used to heat, cool, ventilate, and help control indoor air conditions in residential and commercial buildings.

HVAC Zoning

A method of dividing a building into separate temperature-control areas, often using multiple thermostats and controlled dampers or separate HVAC equipment. Zoning can help accommodate different comfort needs throughout a home.


Back to top ↑

I

Ignition System

The components responsible for lighting fuel in a furnace. Modern gas furnaces commonly use electronic ignition rather than a continuously burning standing pilot light.

Indoor Air Quality (IAQ)

The condition of air inside buildings as it relates to pollutants, ventilation, moisture, and occupant health and comfort. HVAC filtration, appropriate ventilation, source control, and humidity management can all influence indoor air quality.

Infiltration

The uncontrolled movement of outdoor air into a building through openings, cracks, and gaps. Infiltration can increase heating and cooling requirements and introduce outdoor humidity, dust, and pollutants.

Insulation

Material that resists heat transfer. Insulation in attics, walls, and ductwork reduces unwanted heat gain and loss. Proper attic insulation can be especially valuable in Central Texas because of intense summer solar heating.

Inverter Technology

Electronic controls that adjust motor or compressor operating speed to match changing demands. Inverter-driven HVAC systems can provide more continuous operation and finer capacity control than traditional fixed-speed equipment.


Back to top ↑

L

Latent Heat

Energy associated with a change in moisture content or phase rather than a change in dry-bulb temperature. In residential cooling, latent heat removal is associated with condensing water vapor out of indoor air.

Load Calculation

An engineering-based estimate of the heating and cooling capacity required for a building. Load calculations account for building characteristics and climate conditions rather than relying on square footage alone.

Low-GWP Refrigerant

A refrigerant with relatively low global warming potential compared with certain older alternatives. Newer air conditioning equipment increasingly uses lower-GWP refrigerants, including R-32 and R-454B.


Back to top ↑

M

Makeup Air

Outdoor air intentionally introduced to replace air exhausted from a building. Makeup air may be necessary when kitchen exhaust fans, dryers, or other ventilation equipment remove significant amounts of indoor air.

Manual D

An ACCA standard used for designing residential duct systems. It helps determine duct sizes and configurations needed to deliver appropriate airflow.

Manual J

An ACCA standard for calculating residential heating and cooling loads. It accounts for building size, insulation, windows, orientation, climate, infiltration, and other factors to establish equipment capacity requirements.

Manual S

An ACCA standard for selecting residential heating and cooling equipment based on the calculated building loads and manufacturer performance data.

MERV (Minimum Efficiency Reporting Value)

A rating used to compare how effectively air filters capture particles of different sizes. Higher MERV values generally indicate greater particle-removal efficiency, but filters must be compatible with the HVAC system’s airflow capabilities.

Mini-Split System

A heating and cooling system consisting of an outdoor unit and one or more indoor units. Mini-splits are frequently ductless, although some configurations use short duct runs.

Modulating HVAC System

Heating or cooling equipment that adjusts its output across a range of capacities rather than operating only at full capacity. Modulation can improve temperature stability and reduce cycling under part-load conditions.

Multi-Stage Cooling

A system that can operate at more than one cooling capacity. Two-stage systems, for example, typically have a lower-capacity operating mode and a higher-capacity mode for increased cooling demand.


Back to top ↑

N

NATE (North American Technician Excellence)

An industry organization that certifies HVAC service and installation technicians through specialized examinations.

Natural Ventilation

The movement of outdoor air through a building using openings such as windows and vents, driven by wind and temperature differences. Its effectiveness depends on outdoor conditions and building design.


Back to top ↑

O

Outdoor Unit

The portion of a split air conditioning (mini-split) or heat pump system installed outdoors. It typically contains a compressor, fan, and heat-exchanging coil.

Oversized Air Conditioning Equipment

An air conditioning system with greater cooling capacity than a building requires under its design conditions. Oversized equipment can cause short operating cycles, uneven temperatures, and inadequate humidity removal. In Central Texas, proper sizing is especially important because homes must handle both substantial summer heat and varying humidity levels. Equipment should be selected using a professional load calculation, such as ACCA Manual J, and manufacturer performance data.

Oversized HVAC System

Heating or cooling equipment with greater capacity than the building requires under its design conditions. Oversizing can cause excessive cycling, reduced comfort, and, in cooling applications, inadequate moisture removal.


Back to top ↑

P

Packaged HVAC Unit

A system that houses major heating and cooling components in a single outdoor cabinet rather than separating them into indoor and outdoor units.

Plenum

An air distribution chamber connected to HVAC equipment or ductwork. Supply plenums distribute conditioned air to ducts, while return plenums collect air returning to the equipment.

Programmable Thermostat

A thermostat that automatically adjusts temperature settings according to a schedule entered by the user.

Psychrometrics

The study of the physical and thermal properties of moist air, including temperature, humidity, dew point, and enthalpy. HVAC professionals use psychrometric principles to evaluate cooling and dehumidification.


Back to top ↑

R

R-22 Refrigerant

An older hydrochlorofluorocarbon (HCFC) refrigerant formerly common in residential air conditioning. U.S. production and import of new R-22 for servicing existing equipment ended in 2020, although recovered, reclaimed, and previously produced supplies may still be used where permitted.

R-32 Refrigerant

A hydrofluorocarbon refrigerant used in some modern air conditioners and heat pumps. It has a lower global warming potential than R-410A and is classified as A2L, meaning lower toxicity and lower flammability.

R-410A Refrigerant

An HFC refrigerant blend widely used in residential air conditioners and heat pumps installed before the transition toward lower-GWP refrigerants. Existing compatible equipment can continue to be serviced under applicable regulations.

R-454B Refrigerant

A lower-GWP refrigerant blend used in newer air conditioners and heat pumps. It is classified as A2L and must be used only in equipment designed and approved for it.

Refrigerant

A fluid used in air conditioning and heat pump systems to absorb and release heat as it circulates through the refrigeration cycle. Proper refrigerant selection and charging are critical to equipment performance and safety.

Refrigerant Charge

The amount of refrigerant contained in an HVAC system. An incorrect charge can reduce efficiency, affect cooling capacity, and potentially damage equipment.

Refrigerant Leak

An unintended escape of refrigerant from the sealed refrigeration circuit. Leaks can result in reduced cooling performance and require appropriate diagnosis and repair.

Refrigerant Line Set

The pair of tubes, typically copper, that carry refrigerant between the indoor and outdoor units of a split HVAC system.

Relative Humidity (RH)

The percentage of moisture in the air relative to the maximum amount the air could contain at the same temperature. Relative humidity influences comfort, condensation, and indoor moisture conditions.

Return Air

Air drawn from occupied spaces back into the HVAC system for reheating, cooling, or filtration.

Return Air Grille

A grille through which indoor air enters the return duct system on its way back to the HVAC equipment.

Reversing Valve

A component in a heat pump that changes the direction of refrigerant flow, allowing the system to switch between heating and cooling operation.

R-Value

A measurement of resistance to heat flow through an insulating material or assembly. Higher R-values generally indicate greater resistance to heat transfer.


Back to top ↑

S

Seasonal HVAC Maintenance

Preventive service performed to help heating and cooling equipment operate safely, reliably, and efficiently throughout the year. In Central Texas, homeowners often schedule air conditioning maintenance before the summer cooling season and heating inspections before colder winter weather. Maintenance may include checking electrical components, refrigerant performance, airflow, condensate drainage, filters, and other system components.

SEER2 (Seasonal Energy Efficiency Ratio 2)

The current standardized seasonal cooling efficiency rating for most residential central air conditioners and heat pumps. Higher SEER2 ratings indicate greater efficiency under standardized testing, although actual energy use depends on installation, climate, and operating conditions.

SEER (Seasonal Energy Efficiency Ratio)

This is an older standardized measure of seasonal cooling efficiency used for residential air conditioners and heat pumps. SEER has been superseded by SEER2 for current U.S. residential equipment ratings, and the two ratings are not directly interchangeable.

Sensible Heat

Heat associated with a change in air temperature without a change in moisture content. Air conditioning systems remove sensible heat to lower indoor temperatures.

Sensible Heat Ratio (SHR)

The proportion of total cooling capacity devoted to sensible cooling rather than moisture removal. Lower SHR values indicate a greater share of cooling capacity directed toward latent heat removal.

Short Cycling

A condition in which HVAC equipment repeatedly starts and stops after unusually brief operating periods. Potential causes include improper equipment sizing, control problems, restricted airflow, or mechanical faults.

Single-Stage HVAC System

Heating or cooling equipment designed to operate at one primary output capacity when running. Single-stage equipment typically cycles on and off to maintain the thermostat setting.

Smart Thermostat

A thermostat with advanced capabilities such as wireless connectivity, remote control, usage reporting, or automated temperature scheduling. Available features vary by model.

Split System

An HVAC configuration with components divided between indoor and outdoor units. A conventional central air conditioning split system generally uses an outdoor condenser and indoor evaporator coil with a blower.

Static Pressure

The pressure exerted by air within an HVAC system, typically measured relative to surrounding pressure. Excessive external static pressure can indicate airflow restrictions or duct system problems.

Summer Cooling Load

The amount of heat that an air conditioning system must remove to maintain comfortable indoor conditions during hot weather. Central Texas homes can experience substantial cooling loads because of prolonged summer heat, solar exposure, and heat entering through windows, roofs, and walls. Insulation, air sealing, window characteristics, and equipment sizing all influence a home’s cooling requirements.

Supply Air

Conditioned air delivered from HVAC equipment into occupied rooms through supply ducts and registers.

Supply Register

An outlet through which heated or cooled air enters a room. Many registers include adjustable louvers to direct airflow.

Surge Protector

A device designed to protect electrical equipment from certain voltage spikes. HVAC-specific surge protection can help reduce the risk of damage to sensitive components, although it cannot prevent every type of electrical failure.


Back to top ↑

T

Thermal Envelope

The boundary separating conditioned indoor spaces from unconditioned or outdoor environments. It generally includes insulation and air barriers in walls, ceilings, roofs, and floors.

Thermostat

A control device that measures temperature and signals an HVAC system to operate as needed to maintain a selected setpoint.

Thermostatic Expansion Valve (TXV)

A refrigerant-metering device that regulates refrigerant flow into an evaporator based on the evaporator outlet’s superheat conditions.

Ton (Cooling Ton)

A unit of cooling capacity equal to 12,000 BTU/h. A three-ton air conditioning system has a nominal cooling capacity of 36,000 BTU/h. Cooling tons describe capacity, not the physical weight of the equipment.

Two-Stage HVAC System

Equipment that operates at two output levels, generally a lower stage for moderate demand and a higher stage for greater demand.


Back to top ↑

U

Undersized HVAC System

Heating or cooling equipment that cannot provide the capacity required to meet the building’s design heating or cooling load. Undersized equipment may struggle to maintain comfortable indoor temperatures during extreme weather.

UV Air Treatment

The use of ultraviolet radiation, typically UV-C, in equipment designed for treating certain microorganisms or microbial growth. Effectiveness depends on system design, exposure, maintenance, and the target contaminant. UV systems do not replace proper filtration and ventilation.


Back to top ↑

V

Variable-Speed Blower

A blower system capable of operating at different speeds to accommodate changing airflow requirements. Variable-speed operation may improve temperature consistency, noise levels, and system performance when properly configured.

Variable-Speed Compressor

A compressor capable of adjusting its capacity over a range of operating speeds. Unlike a conventional single-stage compressor, it can respond more gradually to changing cooling or heating demands.

Ventilation

The intentional introduction of outdoor air and removal of indoor air to help control indoor pollutants, odors, and moisture.

Ventilation Rate

The quantity of air supplied or exchanged through a ventilation system over a given period, commonly expressed in CFM or air changes per hour.

VRF (Variable Refrigerant Flow)

A heating and cooling technology that regulates refrigerant flow to multiple indoor units according to their individual heating or cooling demands. VRF systems are commonly found in commercial and larger multi-zone applications.


Back to top ↑

W

Weatherization

Improvements that reduce unwanted heat transfer and air leakage through a building. Common measures include air sealing, insulation upgrades, and improvements around windows and doors.

Wet-Bulb Temperature

A temperature measurement influenced by both air temperature and moisture content. It is used in HVAC engineering to evaluate air conditions and certain cooling processes.

Whole-Home Dehumidifier

Equipment designed to remove excess moisture from the air throughout a home, independently of or in coordination with the central cooling system.


Back to top ↑

Z

Zone Control System

A heating and cooling control arrangement that regulates different areas of a building independently. A central ducted zone system may use multiple thermostats and motorized dampers to direct conditioned air where needed.

Zoning Damper

A motorized damper that opens or closes in response to a zone control system, adjusting airflow to designated areas of a building.


Back to top ↑